! Live chat FAQ


E2K-L13MC1 Proximity Switch NEW

USD 175,00

E2K-L13MC1 OMRON Proximity Switch NEW

Datablad E2K-L13MC1 Proximity Switch NEW

OMRON Proximity Switch E2K-L13MC1         

Product Description:

Mount to bypass pipes.

Fit a wide range of pipe diameters: 8 to 11 mm or 12 to 26 mm

Built-in Amplifiers to save space.





Applicable pipes





8 to 11 mm

12 to 26 mm


1 mm max.

1.5 mm max.

Detectable object

Liquid *

Repeat accuracy

±0.2 mm max.

Differential travel

0.6 to 5 mm

0.3 to 3 mm

(Reference value, varies with

pipe size and liquid.)

Power supply voltage

12 to 24 VDC (10.8 to 30 VDC), ripple (p-p): 10% max.

(operating voltage range)

Current consumption

12 mA max.

Control output

Load current

100 mA max.

Residual voltage

1 V max. (Load current: 100 mA, Cable length: 2 m)

Sensing liquid position

Indented mark position (For details, refer to Datasheet)


Detection indicator (orange)

Ambient temperature range

Operating: 0 to 55°C (with no icing or condensation), Storage: -10 to 65°C (with no icing or condensation)

Ambient humidity range

Operating/Storage: 25% to 85% (with no condensation)

Temperature influence

±4 mm of detection level at 23°C in the temperature range of 0 to 55°C

(with pure water or 20% saline solution)

(±6 mm for E2K-L13MC1 with pure water and a pipe diameter of 8 mm)

Voltage influence

±0.5 mm of detection level at the rated voltage in rated voltage ±10% range

Insulation resistance

50 MΩ min. (at 500 VDC) between current-carrying parts and case

Dielectric strength

500 VAC, 50/60 Hz for 1 min between current-carrying parts and case

Vibration resistance

Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions

Shock resistance

Destruction: 500 m/s2 3 times each in X, Y, and Z directions

Degree of protection

IP66 (IEC)

Connection method

Pre-wired Models (Standard cable length: 2 m)

Weight (packed state)

Approx. 70 g


Case, Cover

Heat-resistant ABS

Cable clamp



Two bands, Four slip-proof tubes, Instruction manual

*Stable detection will not be possible in the following cases. Confirm detection capability with the Sensor installed before actual application.

1. If the specific inductive capacity or the specific electric conductivity of the liquid is too low, the liquid position may not be detected since this sensor is a capacitive sensor.

2. If the quantity of liquid is too low or the change in quantity is too low in comparison to the change in liquid level because the pipe is too thin or the walls of the pipe are too thick.

3. If there is a viscous film on the inner pipe wall, large quantities of foam or air bubbles, or excessive buildup of dirt on the inner pipe wall


I følgende tilfeller vil vi gi en gratis utskifting eller full refusjon:

Produktet kan ikke brukes i garantiperioden på grunn av kvalitetsproblemer med produktet

Produktet er skadet under frakt

Produktet blir ikke levert i tide på grunn av vår årsak

Prosessen med gratis utskifting eller full refusjon:

Kjøperne sender en e-post til vår kundeservice for å beskrive problemet og gi bevis (klare bilder, skjermbilder eller video)

Vi vil sjekke problemet innen 1 arbeidsdag. For kvalifiserte tilfeller vil vi gi en gratis utskifting eller full refusjon innen 1-2 virkedager

Hvis en retur er nødvendig, vil vi dekke returfraktkostnadene

E2K-L13MC1 Proximity Switch NEW

Bruttovekt 0.07
credit card